3/15/2023 0 Comments Tiled fireplace wall![]() You’ll also want to vacuum and clean the concrete floor now that the mortar is fully gone to ensure the mortar will stick appropriately. It will also give you a chance to see which tiles are damaged so you can set those aside for use at smaller tile locations in the project. Laying out the tiles will help you see those areas and place the tiles accordingly so you’re not putting all light colors in one area of the surround. Natural tile will have lighter and darker tones throughout. After you’ve selected the tile you want to use for both the wall and floor you’ll want to lay out all of the tiles on a blanket so you can see the different colors of the tile in the same room as the fireplace (having the same light for the preparation as the installation gave me a better idea of what it would look like finished). Once you’ve removed the old tile and mortar it’s time to prepare the site. In some areas I ended up using a Dremel tool. I used chisels and paint scrapers to removed the old mortar. Once I removed all of the old floor tiles I was left with the mortar to clean up. However, a crow bar and a sledge hammer proved much more efficient. ![]() In fact, I broke the masonry chisel after only an hour or so. This broke me off and it didn’t work well. Once through the grout to the concrete underneath I took a masonry chisel and hammered at an angle to separate the tile from the mortar. I took a manual grout remover and scored a place in-between two large, floor tiles. However, I chose to go the cheaper, manual way. If I could do it again I would rent a small jackhammer and save my arms/hands and back A LOT of pain. We did it all by hand, which was a huge pain and took much longer than I had initially planned. This is the time to release your pent up aggression! Removing the existing tile was tough. You might also like how we lowered a breakfast bar, how to paint cabinets, and how to strip paint. See a full video of our tiling process below and/or read on for more details: If you are getting tired I would wait for another day when you’re on top of your destruction game. Be aware that the hardwood floors are prone to scratches so I recommend taking your time when removing the mortar and tiles near the hardwood. Put painters tape on the surrounding hardwood floor and mantel-this will save you detailed repair touch ups down the road. (We used 3”x5” natural marble subway tile for the wall and large 24”x12” natural marble tile for the floor). Take your measurements for what size of tile you want to install and the pattern you want to use. How to Tile a Fireplace Surround (Step by Step) Step 1: AssessĪssess the project. Knee pads (or something soft to take some of the pain off your knees).The grout will say it’s for ¼” or ⅛” grout) Grout (you’ll want to pay attention to the grout you purchase for small or slightly larger grout lines.Tile spacers (2 sizes: one for the wall and one for the floor tiles).We got ours from Home Depot-it was a good price and worked well. Wet tile saw (yes! I always love buying more tools and this was a huge help).This would have added some difficulty to our plan so we decided to forgo it in order to simplify. While many sites do recommend that you do this, our situation allowed us to leave it in place. Disclaimer: we didn’t remove the fireplace mantel. (As with most of our DIYs!)įor our fireplace surround project I removed the floor tiles and tiled over the wall tiles. Or at least that’s what I envision our fireplace surround says now! I’m not a professional tile installer by any means, but I researched enough about how to tile a fireplace to be dangerous! I started this DIY project with a lot of enthusiasm and unrealistic expectations. ![]() That update that says, “Hey, I’m classic, stylish and will endure the changing fads”. It was nice enough 12x12 tile but it lacked that pop. Our fireplace tile surround was looking a bit dated. Tired of looking at a dated fireplace surround? It's easier than you think to learn how to tile a fireplace!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |